SUSE 9.1 startup scripts
From SqueezeboxWiki
From PascalCheffers list post - Jul 30, 2004
#! /bin/sh# Copyright (c) 1995-2004 SUSE Linux AG, Nuernberg, Germany.# All rights reserved.## Author: Kurt Garloff# Please send feedback to http://www.suse.de/feedback/## /etc/init.d/slimserver# and its symbolic link# /(usr/)sbin/rcslimserver#### BEGIN INIT INFO# Provides: slimserver# Required-Start: $syslog $remote_fs# Should-Start: $time ypbind sendmail# Required-Stop: $syslog $remote_fs# Should-Stop: $time ypbind sendmail# Default-Start: 3 5# Default-Stop: 0 1 2 6# Short-Description: SlimServer Free your music!# Description: Slim Devices introduces SlimServer, our powerful# and free Open Source software. Not only will it power Squeezebox,# but it also serves the SLIMP3 network music player or any software# MP3 player on your network. SlimServer runs on Windows, Mac, Linux,# BSD and Solaris.### END INIT INFO## Any extensions to the keywords given above should be preceeded by# X-VendorTag- (X-UnitedLinux- X-SuSE- for us) according to LSB.### Note on runlevels:# 0 - halt/poweroff 6 - reboot# 1 - single user 2 - multiuser without network exported# 3 - multiuser w/ network (text mode) 5 - multiuser w/ network and X11 (xdm)## Check for existence of needed config file and read itSLIMSERVER_CONFIG=/etc/sysconfig/slimservertest -r $SLIMSERVER_CONFIG || { echo "$SLIMSERVER_CONFIG not existing"; if [ "$1" = "stop" ]; then exit 0; else exit 6; fi; }# Read config. $SLIMSERVER_CONFIG# Check for missing binaries (stale symlinks should not happen)# Note: Special treatment of stop for LSB conformanceSLIMSERVER_BIN=$SLIMSERVER_HOME/slimserver.pltest -x $SLIMSERVER_BIN || { echo "$SLIMSERVER_BIN not installed"; if [ "$1" = "stop" ]; then exit 0; else exit 5; fi; }# Source LSB init functions# providing start_daemon, killproc, pidofproc,# log_success_msg, log_failure_msg and log_warning_msg.# This is currently not used by UnitedLinux based distributions and# not needed for init scripts for UnitedLinux only. If it is used,# the functions from rc.status should not be sourced or used.#. /lib/lsb/init-functions# Shell functions sourced from /etc/rc.status:# rc_check check and set local and overall rc status# rc_status check and set local and overall rc status# rc_status -v be verbose in local rc status and clear it afterwards# rc_status -v -r ditto and clear both the local and overall rc status# rc_status -s display "skipped" and exit with status 3# rc_status -u display "unused" and exit with status 3# rc_failed set local and overall rc status to failed# rc_failed set local and overall rc status to# rc_reset clear both the local and overall rc status# rc_exit exit appropriate to overall rc status# rc_active checks whether a service is activated by symlinks# rc_splash arg sets the boot splash screen to arg (if active). /etc/rc.status# Reset status of this servicerc_reset# Return values acc. to LSB for all commands but status:# 0 - success# 1 - generic or unspecified error# 2 - invalid or excess argument(s)# 3 - unimplemented feature (e.g. "reload")# 4 - user had insufficient privileges# 5 - program is not installed# 6 - program is not configured# 7 - program is not running# 8--199 - reserved (8--99 LSB, 100--149 distrib, 150--199 appl)## Note that starting an already running service, stopping# or restarting a not-running service as well as the restart# with force-reload (in case signaling is not supported) are# considered a success.case "$1" in start) echo -n "Starting SlimServer " ## Start daemon with startproc(8). If this fails ## the return value is set appropriately by startproc. startproc -u $SLIMSERVER_USER $SLIMSERVER_BIN $SLIMSERVER_ARGS # Remember status and be verbose rc_status -v ;; stop) echo -n "Shutting down SlimServer " ## Stop daemon with killproc(8) and if this fails ## killproc sets the return value according to LSB. killproc -TERM $SLIMSERVER_BIN # Remember status and be verbose rc_status -v ;; try-restart|condrestart) ## Do a restart only if the service was active before. ## Note: try-restart is now part of LSB (as of 1.9). ## RH has a similar command named condrestart. if test "$1" = "condrestart"; then echo "${attn} Use try-restart ${done}(LSB)${attn} rather than condrestart ${warn}(RH)${norm}" fi $0 status if test $? = 0; then $0 restart else rc_reset # Not running is not a failure. fi # Remember status and be quiet rc_status ;; restart) ## Stop the service and regardless of whether it was ## running or not, start it again. $0 stop $0 start # Remember status and be quiet rc_status ;; force-reload) ## Signal the daemon to reload its config. Most daemons ## do this on signal 1 (SIGHUP). ## If it does not support it, restart. echo -n "Reload service SlimServer " ## if it supports it: killproc -HUP $SLIMSERVER_BIN #touch /var/run/SLIMSERVER.pid rc_status -v ## Otherwise: #$0 try-restart #rc_status ;; reload) ## Like force-reload, but if daemon does not support ## signaling, do nothing (!) # If it supports signaling: echo -n "Reload service SlimServer " killproc -HUP $SLIMSERVER_BIN #touch /var/run/SLIMSERVER.pid rc_status -v ## Otherwise if it does not support reload: #rc_failed 3 #rc_status -v ;; status) echo -n "Checking for service SLIMSERVER " ## Check status with checkproc(8), if process is running ## checkproc will return with exit status 0. # Return value is slightly different for the status command: # 0 - service up and running # 1 - service dead, but /var/run/ pid file exists # 2 - service dead, but /var/lock/ lock file exists # 3 - service not running (unused) # 4 - service status unknown :-( # 5--199 reserved (5--99 LSB, 100--149 distro, 150--199 appl.) # NOTE: checkproc returns LSB compliant status values. checkproc $SLIMSERVER_BIN # NOTE: rc_status knows that we called this init script with # "status" option and adapts its messages accordingly. rc_status -v ;; probe) ## Optional: Probe for the necessity of a reload, print out the ## argument to this init script which is required for a reload. ## Note: probe is not (yet) part of LSB (as of 1.9) test /etc/slimserver.conf -nt /var/run/slimserver.pid && echo reload ;; *) echo "Usage: $0 {start|stop|status|try-restart|restart|force-reload|reload|probe}" exit 1 ;;esacrc_exit